Skylla-i IP21 Battery Charger 24V/100A/230V - (1+1)

A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.

Features

• The right amount of charge for a lead-acid battery: variable absorption time
• BatterySafe mode - preventing damage due to excessive gassing
• Storage mode - less maintenance and aging when the battery is not in use
• Smaller and lighter compared to similar models
• NMEA 2000 Canbus connection
• PowerControl - set a maximum shore power
• Remote Control
• Li-ion (LiFePo4) ready
• The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery
• Rugged - Aluminum epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air
• Circuit boards are protected with an acrylic coating for maximum corrosion resistance
• Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions
• Flexible - Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use
• Synchronized parallel operation - Several chargers can be synchronized with the CAN bus interface
• This is achieved by simply - interconnecting the chargers with RJ45 UTP-cables. 
  

Specifications

• Input Voltage: 230 VAC
• Input Voltage Range VAC: 185-265 V
• Input Voltage Range VDC: 180-350 V
• Maximum AC Input Current at 180 VAC: 20 A
• Frequency Rating: 45-65 Hz
• Power Factor: 0.98
• Charge Voltage Absorption (VDC): 28.8 V
• Charge Voltage Float (VDC): 27.6 V
• Charge Voltage Storage (VDC): 26.4 V
• Charge Current Rating (A): 100 A
• Charge Current Starter Battery (A): 4 A
• Charging Algorithm: 7 Stage Adaptive
• Battery Capacity (Ah): 500-1000 Ah
• Charge Algorithm, Li-Ion: 3 Stage, With On-Off Control or CAN Bus Control
• Temperature Sensor: Yes
• Can be Used as Power Supply: Yes
• Remote On-Off Port: Yes (can be connected to a Li-Ion BMS)
• VE.Can Communication Port: (2) RJ45 Connectors, NMEA2000 Protocol, Galvanically Isolated, Integrated 12 V CAN-Bus Power Supply, 30 VDC Maximum
• Synchronized Parallel Operation: Yes, with VE.Can
• Alarm Relay: DPST AC Rating - 240 VAC/4 A, DC Rating - 4 A up to 35 VDC, 1 A up to 60 VDC
• Forced Cooling: Yes
• Protection: Battery Reverse Polarity (Fuse), Output Short Circuit, Over Temperature
• Operating Temperature: -20 to 60 deg C
• Humidity: Maximum 95% (Non-Condensing)
• Material: Aluminum
• Color: Blue
• Battery Connection: M8 Bolts
• 230 VAC Connection: Screw-Clamp 10 mm²
• Enclosure Rating: IP21
• Standards: Safety EN 60335-1, EN 60335-2-29, Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2, Immunity EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3
• Dimensions: 16 in x 9.9 in x 5.9 in
• Weight: 16 lb
  

Documents 

• Specification Sheet
• Technical Drawing
• Instruction/Installation Manual